Product Warnings Safety Guidelines Required Tools Kit Contents Preparation Tips Installation Procedure Cleaning & Maintenance Warranty In
Followed carefully, these installation instructions willresult in an easy, trouble-free installation of your SwanCorporation product. Any deviations,
To prevent possible water (wicking affect) damage to thewall, install the wall board with a 1/2 inch gap above thebathtub or shower floor side lip, th
Wall Kits With Separate CornerPanels - TF-57, TI-5, TI-NEO-DTF,TI-7236, TI-7248, and TI-7260Note: Faux tile wall kit installation shown. Smoothfinish
Fumes HazardThe fumes from the silicone adhesiveand solvents used by the installer canbe harmful if used in an unventilatedroom. Always work in a wel
Side PanelsMost side panels are designed to fit a certain way.Check for identification tags on the back of panelsand/or bullnose edges, which align wi
5. Trial fit the panel, and make any necessaryadjustments.Fumes HazardThe fumes from the silicone adhesiveand solvents used by the installer canbe har
Apron StripsApron strips are included in some wall kits to give afinished appearance to side panels that project beyondthe front edge of the bathtub o
Back PanelNote: Corner wall units do not have back panels. Ifinstalling a corner shower wall unit, skip to theTemporary Bracing section.1. Trial fit
4. Install the back panel, overlapping the corner panels.Carefully line up any faux grout lines. Press theback panel firmly to the wall. Use even ha
3. Use the measurements to make a cardboardtemplate in order to check for proper fit around theplumbing outlets. Trial fit the cardboard template,and
6. Trial fit the panel, and make any necessaryadjustments.Note: The corner side panel should not extend all theway to the front edge of the bathtub.Fu
9. Carefully position the corner side panel tight againstthe corner and firmly press the surface of the panelagainst the walls. The corner side panel
Do not use oil-based cleaners, such as mineral spirits, toclean the panels. The oil in the cleaner will prevent thepanel from properly adhering to th
Veritek Extension Kits (Tile Design) - TI-33 and TI-55Some extension wall panels have a flange designed to fitagainst the top edge of the existing tub
The Swan Corporation 24 800-325-7008Temporary BracingInstall the temporary bracing to hold the wall panels inplace until the silicone adhesive is comp
4. Insert (wedge) blocks or cross braces between thefront to rear panel braces and the back panelbraces. These blocks or braces must applypressure to
Care and CleaningSwan Corporation Veritek products are stain andabrasion resistant; however, the finish requiresreasonable care.Because cleaning produ
LIMITED WARRANTYFOR COMMERCIAL APPLICATIONSIf a Swan Corporation product covered by this warrantyis found to be defective in materials or workmanshipa
Save these Installation Instructions for future reference.They provide important information on cleaning andmaintenance of Swan Corporation products.w
800-325-7008 3 The Swan CorporationThe Swan Corporation Assurance — if our product isproperly installed and maintained, as stated in theseinstructions
IMPORTANT NOTICE: Indicates that equipment orproperty damage can result if instructions are notfollowed. Read and Understand the ManualIt is the respo
Cutting HazardThe installation of the Swan Corporationproduct may require using power tools. Keephands away from the cutting edge of any toolused in
WARNING: Continued Power Tool HazardTo prevent personal injury or possibledeath, always follow the electrical safetyrecommendations of the power tool
TI-55 Extension Kit (Tile Design)One back panelTwo corner panelsTwo side panelsOne tube of silicone adhesiveOne tube of color coordinated caulkDesigne
Unpack Carton Use care when opening the box so that you do notdamage the panels. This product is shipped to you or your retail centerafter careful i
Swan Corporation panels can be installed over a varietyof products. If you intend to apply the panels to anysurface other than those described, consu
Commentaires sur ces manuels